|
|
|
|
Polyurethane Beach Wheels |
![]() |
![]() |
![]() |
![]() |
|---|---|---|---|---|
| Product Name & Number |
24cm PU Beach Wheel WZ1-24U |
30cm PU Beach Wheel WZ1-30U |
42cm PU Beach Wheel WZ1-42U |
49cm PU Beach Wheel WZ1-49U |
| Dimensions* | 9.4 x 4.8" (24 x 12.3 cm) | 11.8 x 7" (30 x 18 cm) | 16.5 x 7.9" (42 x 20 cm) | 19.3 x 9" (49 x 23 cm) |
| Width at Bushing/Bearing | 5" (12.8 cm) | 7.3" (18.5 cm) | 7.8" (19.8 cm) | 7.8" (19.8 cm) |
| Max. Payload per Wheel | 88 lbs (40 kg) |
121 lbs (55 kg) |
176 lbs (80 kg) |
264 lbs (120 kg) |
| Weight | 1.5 lbs (0.7 kg) |
2.91 lbs (1.32 kg) |
5.5 lbs (2.5 kg) |
6.1 lbs (2.78 kg) |
| Materials | Tire: Polyurethane Hub: Polypropylene |
Tire: Polyurethane Hub: Polypropylene |
Tire: Polyurethane Hub: Polypropylene |
Tire: Polyurethane Hub: Polypropylene |
| Ideal & Ship Pressure | 2.5 psi (0.17 bar) | 2.5 psi (0.17 bar) | 2.5 psi (0.17 bar) | 2.5 psi (0.17 bar) |
| Pressure Range | Low Pressure 2–4 psi (0.14-0.28 bar) | Low Pressure 2–4 psi (0.14-0.28 bar) | Low Pressure 2–4 psi (0.14-0.28 bar) | Low Pressure 2–4 psi (0.14-0.28 bar) |
| Temperature Range | 5 to 167 F (-15 to 75 C) | 5 to 167 F (-15 to 75 C) | 5 to 167 F (-15 to 75 C) | 5 to 167 F (-15 to 75 C) |
| Works on |
|
|||
| Price | ||||
Sold individually, not as pairs. |
|
|||
| * With tire pressure 2.5 psi at sea level and at a temp range of 75-80° F (24-26.5° C). |
||||
| Note: Wheel dimensions may vary temporarily by up to +/- 1" (2.5 cm) in diameter and/or width, depending on temperature and elevation. | ||||
Read a review of the
24cm wheels on Hobie Forums.
Here's an excerpt from the review, "Load capacity is up to 88 lb. per wheel. I'm not recommending the following procedure, but the local dealer's demo boat was loaded with concrete here for a combined weight of 190 lb sitting on the wheels shown here. This was rolled this over the wood hurdles to see if the wheels would pinch the rims. Not even close."
Polyurethane |
WZ3-24U-T |
|
|
|
|---|---|---|---|---|
| See our repair page for instructions on how to install | ||||
The Twist Lock Knob (TLK) is a knob that attaches to the end of our 1/2" axle that has a special groove that the TLK locks on to. The TLK makes it easy to attach and unattach wheels from your axle. In the case of this wheel, the TLK is actually attached to the hub so you won't lose it.
This page can be found by searching for: balloon wheels, sand wheels, beach wheels, soft wheels, all terrain, wheels, baloon wheels, fatso, fat wheels




